Milwaukee 2760 20 vs 2853 20 (The 360 Guide)

Milwaukee is one of the most popular brands when it comes to impact drills. But with all their models, it’s a little confusing to decide which one to choose. People often find themselves wondering, which Milwaukee impact drill should they buy.  

So, between Milwaukee 2760 20 vs 2853 20, what are the differences? 

2853-20 is a fuel driver whereas 2760-20 is a fuel surge drive. 2853-20 has a greater torque rating and speed than 2760-20. Also, the maximum chuck size of  2853-20 is greater than 2760-20. 2760-20 has a little more BPM and length than 2853-20.

Quick Overview of 2853-20 Milwaukee and Milwaukee 2760-20

Factors Milwaukee 2760 20 Milwaukee 2853-20
Speed 3000 RPM 3600 RPM
Torque Rating 450 2000
Overall length 5” 4.59”
BPM 4250 4000
Maximum Chuck Size 6.35 mm 13 mm
Noise Less More
Price $119-122 $95- 105

If you are new at this, the quick comparison might be still confusing for you. For that, we have prepared an in-detailed comparison between these too. 

Milwaukee 2853-20 vs 2853-22: In-depth Comparison

This detailed comparison will help you decide better which should you choose.

Factor 1: Speed

The higher the speed, the maximum rotation the driver can perform in one minute. Most of the impact drivers have an average speed of 0-2500 RPM

Milwaukee 2760-20 driver has a speed of 0- 3000 RPM which is already more than average. But 2853-20 will provide you with more speed. It can go up to 0-3600 RPM

But you have to remember, that this maximum RPM is for the “No Load” situation. That means when the driver isn’t driving any screws. But the trigger is pulled to the fullest. Drilling on hard materials will decrease the speed. 

However, the 2853-20 model will still have more RMP with a load than the 2760-20. 

Verdict on Speed:

If your priority is to do the job more quickly, go for 2853-20. 

Before going to the next point we just want to remind you of something. Don’t forget to take care of your impact drivers. They are very delicate. 

Factor 2: Torque Rating

In impact drivers, torque rating is a very important factor to consider. Suppose a driver has a higher range of torque. Then you can set it as per your requirement for any work. From fastening small screws to bigger ones. 

But if the driver has a low torque rating, it can only fasten the small screws. Typically, we will recommend choosing a driver with a torque rating of 1600- 1800 on average. 

A good thing about the 2853-20 model is that it has a torque rating of 2000. Which is a lot. It can be used in more versatile jobs. 

On the other hand, the 2760-20 model has a torque rating of 450 only. So, this will allow you to use it only for fastening smaller screws. 

Verdict on Torque Rating:

we will recommend you go for the 2853-20 model if you wanna perform more work. But if you only have a job that requires lower torque, you can go for 2760-20. 

Factor 3: Overall Length

Usually, Milwaukee impact drivers are 5-6 inches in length. 2760-20 also has a length of 5 inches. 

But with a 2853-20 model, you will get another advantage. It is claimed to be the most compact Milwaukee driver till now. So, you can easily access spaces that are tighter. 

Verdict on Driver Length:

If you wanna fasten crews in a tighter space, the 2853-20 model will come handier. 

Factor 4: BPM

BPM or blows per minute indicates how rapidly the impact driver can repeat the process. The 2760-20 model has a little more BPM than the 2853-20 model. 

The 2760-20 model provides 4025 BPM, whereas the 2853-20 model provides 4000 BPM. Although 4000 BPM is enough for almost all of the work. 

Verdict on BPM:

2760-20 provides a little higher BPM than 2853-20. But the significance isn’t much. So, you can consider other features for deciding. 

Factor 5: Maximum Chuck Size

Chuck size indicates the highest size of bit you can insert into the driver. The more the maximum chuck size is, the more versatile sizes of bits that can be inserted. 

The average chuck size can be found in impact drivers are 10 mm. The model 2760-20 has only a 6.35 mm maximum chuck size. It’s below average. And this drive only can take small-sized bits. 

On the other hand, the 2853-20 model has a 13 mm maximum chuck size. So it can take almost all sizes of bits. 

Verdict on Maximum Chuck Size:

In the case of the maximum chuck size, the 2853-20 model will serve you better. 

Factor 6: Noise

Impact drivers usually make a lot of noise. It’s a little annoying especially when you work at night. 

Milwaukee introduced a feature “Surge” in the 2760-20 model. That means it’s a hydraulic driver. Let’s put this simply. This kind of driver makes 50% less vibration and noise than the regular ones. 

On the other hand, in the 2853-20 model, this option isn’t available. So these are noisier. 

Verdict on Noise:

If you wanna reduce noise pollution and don’t wanna annoy your neighbor, go for 2760-20. But do it only if other requirements of yours match. 

Sometimes you may notice a strange but common problem in your Milwaukee drivers. The charging indicator is green but the driver is not charging. You can repair this on your own or you can go to a repair shop. 

Factor 7: Price

No matter how great the features are, we always have to match our budget. Usually, when you get more features from a product, the price automatically raises. But in the case of  2853-20 and 2760-20, there’s a little difference. 

You will find the model 2853-20 in between $95- 105. But for the 2760-20 model, you have to spend $ 119-122. It can be because of the “surge” added to the 2760-20 model. 

Verdict on Price:

If decreasing noise is not your priority, you should go for the 2853-20 model. 

Now you can decide which one you should buy. You can check out both Milwaukee drivers here. 

We hope you will find these helpful. Although impact drivers and wrenches are very handy. There are some times when you can not use an impact wrench. So, before using impact tools, know if it is suitable. 

FAQs

How Much Torque Is Enough for an Impact Driver?

Usually, 1500–1800 in-lbs is enough for impact drivers. With this torque range, you can use the driver from fastening small screws to bigger ones. A higher torque range than this won’t be much of a problem. But lower torque will limit your driver usage only to fasten smaller screws. 

What’s the Difference Between Milwaukee Fuel and Surge?

The main difference between Milwaukee Fuel And Surge is that Surge is a hydraulic driver. Surge drivers can reduce up to 50% of the vibration and noise the driver causes. 

Is Ryobi as Good as Milwaukee?

No, Ryobi isn’t as good as Milkauwee. Milwaukee is one of the best brands for impact tools. It has more features than Ryobi. It is faster and lasts longer than the Ryobi tools too. But Ryobi tools are much more reasonable. If you need a driver for light use, you can go for it. 

Conclusion

So that’s all from us on Milwaukee 2760 20 vs 2853 20. The 2853-20 model is mostly better in all aspects. It is reasonably priced too.

But if you wanna do your construction job a little quietly, go for the 2760-20 model. 

All the best and have a good day!

Jim Boslice

Leave a Comment

Your email address will not be published. Required fields are marked *